Specifications

Voltage supply 9...32 VDC (+/-10 %)

 

Additional information is provided in Technical details about the energy supply.
Power consumption 1)

typ. 15W (without sensors)

max. 27W (without sensors)
Integrated rechargeable buffer battery Rechagreable Li-Po battery with 500 mAh for sending a notification in the event of a power failure.

 

Additional information is provided in Technical details about the integrated rechargeable buffer battery.
Housing

Material:

Weight:

Degree of protection:

Dimensions (WHD)

     Data logger:

     Extension modules:

Lexan/Noryl

480 g 1)

IP20 / IP40 (connection area/operating area)

 

70 x 92 x 63 mm (without antenna)

70 x 92 x 57 mm

Operating temperature -20...+60 °C
Air humidity 15...90 % RH non-condensing
Storage temperature -40...+85 °C
Charging temperature

(rechargeable buffer battery)

 0 ...+45 °C
Display

Data logger:

  • RGB LED to indicate the operating state and error codes

Extension modules:

  • LED signalling that the device is ready for operation
  • LEDs signalling the state of communication of the CAN interface
  • LEDs to indicate the switching states of the relais
Operation Button to trigger
  • a new connection establishment if the online connection has been aborted
  • a complete device synchronisation with established online connection
  • a connection establishment in interval mode

In any case, the server assignments are also checked.
System time Hardware real-time clock with its own buffer battery (service life >10 years) and automatic time synchronisation with the server.

 

Additional information is provided in Technical details about the system time.
Antenna connector 1 x SMA-F for mobile radio
Universal inputs

15 x analogue or digital 2)

Modes:

  • 0/0...20mA: Resolution 6,36 µA, max. 23,96 mA, load 96 Ω
  • 0...2V: Resolution 610 µV, max. 2,5 V, load 10k086
  • 0...10V: Resolution 7,97 mV , max. 32 V, load 4k7
  • Digital: low <0,99 V, high >2,31 V, max. 32 V, load 4k7
  • Day counter: min. pulse length 1 ms, max. 32 V, load 4k7
  • Interval counter: min. pulse length 1 ms, max. 32 V, load 4k7

 

Additional information is provided in Technical details about the universal inputs.
Outputs

2 x relay on data logger:

  • Umax: 32 V
  • Imax: 2 A

 

2 x relay on input extension:

  • Umax: 230 V AC
  • Imax: 2 A

 

6 x relay on output extension (2 groups for different potentials):

  • Umax: 230 V AC

  • Imax: 3 A 3)

 

3 x analogue output on output extension:

  • active, galvanically separated
  • max. load voltage: 21,5 V
  • max. load (21,5 V , 24 mA ): 890 Ω
  • Iout max: 24 mA

Modes:

  • 0-20 mA
  • 4-20 mA
  • 0-24 mA

 

Additional information is provided in Technical details about the outputs.
USB interface 1 x mini-B USB 2.0 slave for the connection to a PC. The DeviceConfig configuration program must be installed on the PC to enable communication with the myDataconC3+ .

 

Additional information is provided in Technical details about the USB interface.
Data memory Internal flash memory for up to 27.832 measuring cycles

 

Additional information is provided in Functionality of the internal data memory.
Data type State of the relay of the output extension: u8 (8Bit unsigned)

other measurement data: f32 (32Bit floating point)

Data transmission

M1/NB1 EU (myDatalogC32x M1/NB1 EU ):

  • LTE B1, B2, B3, B4, B5, B8, B12, B13, B14, B18, B19, B20, B25, B26, B28, B66 (M1)
  • LTE B1, B2, B3, B4, B5, B8, B12, B13, B17, B19, B20, B25, B26, B28, B66 (NB1/NB2)

2G/4G World (myDatalogC32x 2G/4G World ):

  • 2G GPRS 900MHz / 1800MHz
  • 2G GPRS 850MHz / 1900MHz
  • LTE FDD B1, B2, B3, B4, B5, B7, B8, B12, B13, B17, B18, B19, B20, B25, B26, B28, B66
  • LTE TDD B34, B38, B39, B40, B41

SIM The myDataconC3+ is equipped with an integrated SIM chip.

1) Applies to the maximum configuration consisting of data logger + input extension + output extension. Specifications of the individual componens are provided in the relevant user manuals.

2) 3 x universal input on data logger and 12 x universal input on input extension

3) applies to a single relay of the group. However, the current on the entire root (CC) must not exceed 6 A .